Reply to thread

Message: <blockquote data-quote="apikaluda?" data-source="post: 24117320" data-attributes="member: 470863">Machan mekanam use karala ne.....software eka wagema ethi kiyala hithanawa....machan mama me kiyana widiha weda kale nettan software eka install karala eken balanna....anika web editor use karanne ai? wishesha hethuwak thiyenawada?Onna code eka Serial monitoring walata eduwa....e kiyanne ape variables wala agayan board eka read karana agayan apita serial monitoring karanna puluwan. code eka mehemai:const int ForwardLimitSwitchPin = 2;const int ReverseLimitSwitchPin = 3;const int StepperStepPin = 4;const int StepperDirectionPin = 5;const int LimitSwitchActivated = LOW; // Limit switch grounds pinconst int StepperMaxRPM = 100;const int buttonPin = 6;     // the number of the pushbutton pin (choose the correct pin here)bool ispushbuttonpressed = false; // Boolean to store push button logic int buttonState = 0; //**correctionStepper stepper(200, StepperStepPin, StepperDirectionPin);char codeSection[] = "start"; //use to check code only (remove it once code is finalized!)void setup() {  pinMode(ForwardLimitSwitchPin, INPUT_PULLUP);  pinMode(ReverseLimitSwitchPin, INPUT_PULLUP);  stepper.setSpeed(StepperMaxRPM);  pinMode(buttonPin, INPUT); //declare push button signal as an input  Serial.begin(9600); //Serial Monitoring ON  Serial.println("Push button state\t\tForward LS State\t\tReverse LS State\t\tCode Section");}void loop() {  buttonState = digitalRead(buttonPin); // read push button on-off  if (buttonState == LOW) { //**LOW (not HIGH)    ispushbuttonpressed = true;  }  // Step forward until the limit switch is activated (forward rotating when hits S1) - LOOP 1  if ((ispushbuttonpressed == true) && (digitalRead(ForwardLimitSwitchPin) != LimitSwitchActivated)) {  //**corrections added    ReverseLimitSwitchPin = "inside loop one";    while (digitalRead(ForwardLimitSwitchPin) != LimitSwitchActivated) {    stepper.step(1);    }    ispushbuttonpressed == false; //re-set to avoid motor turning backward once reached S2  }    // Step reverse until the limit switch is activated (forward rotating when hits S2) - LOOP 2  else if ((ispushbuttonpressed == true) && (digitalRead(ReverseLimitSwitchPin) != LimitSwitchActivated))  //**corrections added    codeSection[] = "inside loop two";    while (digitalRead(ReverseLimitSwitchPin) != LimitSwitchActivated) {    stepper.step(-1);    }    spushbuttonpressed == false; //re-set to avoid motor turning backward once reached S1  }   Serial.print(buttonState);   Serial.print("\t\t\t");   Serial.print(ForwardLimitSwitchPin);   Serial.print("\t\t\t");     Serial.print(ReverseLimitSwitchPin);   Serial.print("\t\t\t");   Serial.println(ReverseLimitSwitchPin);} Code eka upload karala Tools>>Serial Monitor (nettan short cut keys walinnam ctrl+shift+M) balannaEthakota podi wenama window ekak open wela eke agayan pennanawa....issella karala balanna....ethakota anith tika kiyannam...Code eka balanna....eeta passe Serial Monitor daala push button, limit switches obala balanna ethakota serial monitor eke agayan wenas wenawa...balala kiyanna....awulaknam kiyanna...</blockquote>

Verification: Nawa warak dahaya keeyada? (Namaya wadi kireema dahaya)

Top Bottom