Reply to thread

Message: <blockquote data-quote="Sachchaka" data-source="post: 10564057" data-attributes="member: 149450">There is some procedure that you have to follow I think every information is covered here<a href="http://cws.internet.com/article/2352-.htm" target="_blank">http://cws.internet.com/article/2352-.htm</a>The first step in setting up a peer-to-peer wireless network is to establish a common workgroup environment for the five PCs you mention. This means setting all the PCs to use the same workgroup name (for example, "WORKGROUP" or "OFFICE"). Next you'll need to configure the IP network information for each PC. In a peer-to-peer environment such as this (one without an access point or wireless router), you'll need to configure each PC with a static IP address and a common subnet mask. So, for example, each PC would be given a subnet address of 255.255.255.0 and an IP address of 192.168.0.x. I would suggest using 192.168.0.10 for the first IP address and then increasing in increments of 1. If you're wondering why we didn't start with 192.168.0.1, it's because that address is usually reserved as the router/gateway address. By leaving it available, if you ever decide to add a broadband Internet connection to your network, you won't have to re-address every PC. And by leaving the lower numbers free, it not only gives you room to grow but also allows you to maintain some structure with your IP assignments — i.e. servers and routers use addresses below 10; workstations and printers use 10 and above. With the IP information in place, the next step is to move on to configuring your wireless network parameters. By default, most wireless network adapters ship in what is called "Infrastructure Mode." This is the mode used when an access point or wireless router is present in your network. For wireless networks running in peer-to-peer mode, this setting needs to be changed to "Ad-Hoc Mode." This allows the cards to talk to each other and not search for an access point or router. If you're interested, additional information on Ad-Hoc networks can be found here. Once that has been completed, verify that the wireless cards are configured to use the same settings. All of the wireless adapters should be using a common service set identifier or SSID (just like the workgroup name), and they should be transmitting data on the same channel. Wireless adapters from different vendors sometimes default to different channels, so verify your settings. Additionally, during this stage all levels of WEP or WPA encryption should also be disabled. While I understand you will want your data to be secure, WEP/WPA can be extremely problematic to configure, particularly from cards made by different vendors. Once you have conductivity between your non-encrypted wireless systems, then you can worry about successfully enabling WEP or WPA. When you do finally enable it, take your time and ensure that the encryption settings on all the cards are set to the same encryption level (64-bit, 128-bit, and so on) and are using identical encryption keys. As far as your printer goes, all you have to do is physically connect it to your desktop PC and then share it. In your question, you didn't indicate which version of Windows you were using, so I'm going to outline the steps for enabling it under Windows XP. This procedure is pretty similar in all versions of Windows with a couple of minor differences. So if you are using a different version of Windows, don't sweat it. The procedure for sharing a drive, folder, or printer is pretty much the same. To share a folder, simply open Windows Explorer and locate the folder you want to share. Right-click it and select Sharing and Security. Go to the Sharing tab and select the option Share this folder on the network.  If you wanted to share a drive, you would check the box that reads You understand the risk but still want to share the root of the drive. After you click OK, a small hand will appear under the drive or folder you selected. This indicates that sharing has been enabled and that the folder or drive will now be accessible from the other PCs. Sharing a printer is almost identical to sharing a folder or drive. Just right-click on the printer you want to share and select Properties. Go to the sharing tab and select "Share this Printer." Give the printer a shared name and press OK. The hand will appear and the printer will now be shared. If you follow these general guidelines you should find yourself up and running in no time. Good Luck!</blockquote>

Verification: Winadiyakata thappara keeyak tibeda?

Top Bottom