Reply to thread

Message: <blockquote data-quote="fviran" data-source="post: 4117236" data-attributes="member: 52932"> ~~~~ AIRTEL GPRS HACKING ~~~~, HACK GPRS AND ENJOY INTERNET ON YOUR PC (TESTED WORKING), HACK GPRS AND ENJOY INTERNET ON YOUR PC (TESTED WORKING) NOT FOUND BY me!!! 1.FREE gprs, mms, airtel live, morelets start from free gprs via airtel livepls note this trick works only on mobile with multi channel supportit was not found by me .u need a PC or a Laptop and the required connectivity tools ,ie.,Serial/USB cable OR Infrared Device OR Bluetooth dongl.........~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~NOW D GAME BEGINS~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~1) Activate Airtel Live! ( It's FREE so no probs)2) Create 1 Airtel gprs data accounts and select theFIRST as the active profile.CODEUnder DATA COMM~~~~~~~~~~~~GATEWAY : 100.1.200.99APN : airtelfun.comUSERNAME : blankPASSWORD : blankPASS REQ : OFFALLOW CALLS : AUTOMATICIPADDRESS :100.1.200.99DNSADDRESS 1 : 202.56.230.5DNSADDRESS 2 : 202.56.240.5DATA COMP : OFFHEADER COMP : OFFUnder INTERNET PROFILES~~~~~~~~~~~~~~~~INTERNET MODE : HTTP or WAP (both works)USE PROXY : YESIP ADDRESS : 100.1.200.99PORT : 8080USERNAME :PASSWORD :3) Connect your mobile to the PC (or Laptop) and install the driver foryour mobile's modem.4) Create a new dial-up connection using the NEW CONNECTIONWIZARD as followsConnecting Device : Your mobile's modemISP Name : Airtel (or anything you like)Phone Number : *99***1#Username and Password : blank5) Configure your browser and download manager to use the proxy100.1.200.99 and port 8080.( My advice is to use Opera since youcan browse both wap and regular websites)6) Connect to the dial-up account. You will be connected at 115.2kbps (NOTE* 115.2 KBPS IS A SPEED BETWEEN UR PC AND PHONE ).7) Pick up your mobile and try to access any site. You will get "AccessDenied."(except for Airtel Live!). IT DOES NOT MATTER.Keep the mobile down.8 ) On the PC ( or Laptop) open your browser, enter any address ,press ENTER and.WAIT9) After a few seconds the page will start to load and you have theWHOLE internet at your disposal.Quote: pls Note If u are getting any error wile dialing a dial up connection than go toControl panel>> Phone and modem>>>select modem and click on its properties >>advancedcntdand enter the following initialization commandsCODEAT+CGDCONT=1, "IP","airtelfun.com","",0,0and click on ok now connect to gprs it will be connected without any errorto improve the speedgo to run and typeping -t 100.1.200.99and pres enterand minimize the window it will improve the speed delete...........based on my experience u will get some of teh errors liek thisCODE"Error 734: The PPP link control protocol was terminated"possible solutionSYMPTOMS:-If you try to establish a Point-to-Point Protocol (PPP) dial-up connection, you may receive the following error message:Error 734: The PPP link control protocol was terminated.As a result, you cannot establish a dial-up connection.SE:-This issue may occur if either of the following conditions are true: • Multi-link negotiation is turned on for the single-link connection.-or-• The dial-up connection security configuration is incorrectly configured to use the Require secured password setting.RESOLUTION:-To resolve this issue: 1. Click Start, point to Settings, and then click Network and Dial-up Connections.NOTE: For Windows Server 2003, click Start, point to Control Panel, and then point to Network Connections.2. Right-click the appropriate dial-up networking connection, and then click Properties.3. Click the Networking tab, and then click Settings.4. Click to clear the Negotiate multi-link for single link connections check box (if it is selected).5. Click OK, and then click OK.6. Double-click the connection, and then click Dial. • If this procedure resolves the issue and you can establish a dial-up connection, you do not have to follow the remaining steps in this article.• If this does not resolve the issue and you cannot establish a dial-up connection, go to step 7 to continue to troubleshoot this issue.7. Right-click the connection, and then click Properties.8. Click the Security tab.9. Under Security options, click Allow unsecured password in the Validate my identity as follows box, and then click OK.10. Double-click the connection, and then click Dial to verify that you can establish a dial-up connection.</blockquote>

Verification: Dawasata paya keeyak thibeda?

Top Bottom