Reply to thread

Message: <blockquote data-quote="coolkasun" data-source="post: 4104485" data-attributes="member: 123068">Motorola 8400-------------(Note: pause means the * key held in until box appears)To activate RBS type: [pause] [pause] [pause] 1 1 3[pause] 1 [pause] [ok]You now have to press the [MENU] and scroll to the 'EngField Options' function with the keys, and enable it.De-activate RBSTo de-activate RBS type: [pause] [pause] [pause] 1 1 3[pause] 0 [pause] [ok]This only works with some versions of software.These countries has been reported working:ES, AU, NL, BEWhat's the use of RBS:Get Distance From Base Station - Place a call, when itis answered, press [MENU] until 'Eng Field Option' isdisplayed, press [OK], select 'Active Cell', press [OK],press [MENU] until 'Time Adv xxx' appears, where xxx isa number. Multiply this number by 550, and the result isthe distance from the RBS (Radio Base Station), inmeters.Get Signal Quality - press [MENU] until 'Eng FieldOption' is displayed, press [OK], select 'Active Cell',press [OK], press [MENU] until 'C1' appears. This is thesignal quality. If it becomes negative for longer than 5seconds, a new cell is selected.Pin OutsNumbered right to left, keypad up, battery down looking1. Audio Ground2. V+3. True data (TD) (input)4. Downlink - Complimentary data (CD) (input)5. Uplink - Return data (RD) (output)6. GND7. Audio Out - on/off8. Audio In9. Manual Test - ???10. Battery Feedback11. Antenna connectorMotorola 8700--------------*#06# for checking the IMEI (International Mobile Equipment Identity)Activate RBS(Note: pause means the * key held in until box appears)To activate RBS type: [pause] [pause] [pause] 1 1 3[pause] 1 [pause] [ok]You now have to press the [MENU] and scroll to the 'EngField Options' function with the keys, and enable it.De-activate RBSTo de-activate RBS type: [pause] [pause] [pause] 1 1 3[pause] 0 [pause] [ok]This only works with some versions of software.These countries has been reported working:AU, IT, SG, DE, ES, ZAWhat's the use of RBS:Get Distance From Base Station - Place a call, when itis answered, press [MENU] until 'Eng Field Option' isdisplayed, press [OK], select 'Active Cell', press [OK],press [MENU] until 'Time Adv xxx' appears, where xxx isa number. Multiply this number by 550, and the result isthe distance from the RBS (Radio Base Station), inmeters.Get Signal Quality - press [MENU] until 'Eng FieldOption' is displayed, press [OK], select 'Active Cell',press [OK], press [MENU] until 'C1' appears. This is thesignal quality. If it becomes negative for longer than 5seconds, a new cell is selected.Motorola CD 160---------------Press menu and type one of these numbers and press OK:11 = Status Review13 = Available Networks14 = Preferred Networks22 = Select Keypad Tones25 = Require SIM Card PIN26 = Language Selection32 = Repetitive Timer33 = Single Alert Timer34 = Set IN-Call Display35 = Show Call Timers36 = Show Call Charges37 = Call Charge Settings38 = Reset All Timers43 = Reset All Timers45 = Show Last Call46 = Total For All Calls47 = Lifetime Timer51 = Change Unlock Code52 = Master Reset53 = Master Clear (Warning!! May result in deleting the Message Editor!!!)54 = New Security Code55 = Automatic Lock63 = Battery Saving ModeFree call tip1 Enter the phone number2 Enter OK3 Type *#06#4 Press Button C5 And finally press the button for power off.You should now be able to talk without being billed.Motorola CD 520----------------Press menu and type one of these numbers and press OK:11 = Status Review13 = Available Networks14 = Preferred Networks22 = Select Keypad Tones25 = Require SIM Card PIN26 = Language Selection32 = Repetitive Timer33 = Single Alert Timer34 = Set IN-Call Display35 = Show Call Timers36 = Show Call Charges37 = Call Charge Settings38 = Reset All Timers43 = Reset All Timers45 = Show Last Call46 = Total For All Calls47 = Lifetime Timer51 = Change Unlock Code52 = Master Reset53 = Master Clear (Warning!! May result in deleting the Message Editor!!!)54 = New Security Code55 = Automatic Lock63 = Battery Saving ModeFree call tip1 Enter the phone number2 Enter OK3 Type *#06#4 Press Button C5 And finally press the button for power off.You should now be able to talk without being billed.Motorola d460--------------#06# for checking the IMEI (International Mobile Equipment Identity)Activate RBS(Note: pause means the * key held in until box appears)To activate RBS type: [pause] [pause] [pause] 1 1 3[pause] 1 [pause] [ok]You now have to press the [MENU] and scroll to the 'EngField Options' function with the keys, and enable it.De-activate RBSTo de-activate RBS type: [pause] [pause] [pause] 1 1 3[pause] 0 [pause] [ok]This only works with some versions of software.What's the use of RBS:Get Distance From Base Station - Place a call, when itis answered, press [MENU] until 'Eng Field Option' isdisplayed, press [OK], select 'Active Cell', press [OK],press [MENU] until 'Time Adv xxx' appears, where xxx isa number. Multiply this number by 550, and the result isthe distance from the RBS (Radio Base Station), inmeters.Get Signal Quality - press [MENU] until 'Eng FieldOption' is displayed, press [OK], select 'Active Cell',press [OK], press [MENU] until 'C1' appears. This is thesignal quality. If it becomes negative for longer than 5seconds, a new cell is selected.Motorola V3688---------------#06# for checking the IMEI (International Mobile Equipment Identity)Enhanced Full Rate Codec (EFR):To Enable EFR press [][][] 119 [] 1 [] OK.To Disable EFR press [][][] 119 [] 0 [] OKNOTE: Nothing appears on Screen.Ericsson Mobile Secret Codes:T10*#06# for checking the IMEI (International Mobile Equipment Identity)>*<<*<* for checking the firmware revision information (software release)>*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language.Shortcut for Last Dialed call menuIf you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following keystroke instead: First '0' then '#'.Access menu without Sim cardTo access to the menu in your phone without having a card inside do the following: type **04*0000*0000*0000# When display say "Wrong Pin" press NO and you have access to the all menus: Info, Access, Settings, Calculator, Clock, Keylock On?, Mail, Phone book. NOTE if you try this on your phone may stop at Keylock On? menu and you΄ll have to take your battery out to turn the phone on again. And this will not care about Phone lock!A way to (un)lock your cell phone on to the network(subset):1. Press <**<2. Then on the display appear and give you two choices: Lock to Network ? and Lock to Network subset? (Use arrow keys to select)3. Enter the NCK number (code is provided by the SP)4. You have 5 attemps to do this5. Then your cell phone will work 'only' with the networkWarning: The Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator. To activate/deactivate this lock one needs a special secret code that is not available to the end user. Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times, the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM.Message ReportWhen you writing a message, place at the start of it the code *0# and continue with your message. It's job is like nokias report. It gives you information about the sended message.T18*#06# for checking the IMEI (International Mobile Equipment Identity) Information you get from the IMEI:XXXXXX XX XXXXXX XTAC FAC SNR SPTAC = Type approval codeFAC = Final assembly codeSNR = Serial numberSP = SpareTo access SIM-Locking menu of your phone, press: < * [CLR] <Be careful or you may lock your phone.Message ReportWhen you writing a message, place at the start of it the code *0# and continue with your message. It's job is like nokias report. It gives you information about the sended message.T28*#06# for checking the IMEI (International Mobile Equipment Identity)>*<<*<* for checking the firmware revision information (software release)>*<<*<*> 1-row text strings. if pressing yes you can check the phones text programming in currently selected language.>*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language.The Service Provider (SP) LockThe Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.To activate/deactivate this lock one needs a special secret code that is not available to the end user.Here is how to activate the menu:<**< Lock to Network? if pressing yes you have 5 attempts to enter NCK.<**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK.Warning: Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times, the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM.Shortcut for Last Dialed call menuIf you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following keystroke instead: First '0' then '#'.Message ReportWhen you are writing a message, place at the start of it the code *0# and continue with your message. It's job is like nokias report. It gives you information about the sended message.388*#06# for checking the IMEI (International Mobile Equipment Identity)*#0000# to reset the phones menu-language to English.>*<<*<* for checking the firmware revision information (software release)>*<<*<*> 1-row text strings. if pressing yes you can check the phones text programming in currently selected language.(298 entries)>*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language.(160 entries?)The Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.To activate/deactivate this lock one needs a special secret code that is not available to the end user. (not even to you... or is it ? in case please let me know!)<**< Lock to Network? if pressing yes you have 5 attempts to enter NCK.<**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK.Warning: Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times,the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM.Shortcut for Last Dialed call menu...If you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following keystroke instead: First '0' then '#'.Access menu without Sim card ...To access to the menu in your phone without having a card inside do the following: type **04*0000*0000*0000# When display say "Wrong Pin" press NO and you have access to the all menus: Info, Access, Settings, Calculator, Clock, Keylock On?,Mail, Phone book. NOTE if you try this on the GH688 your phone may stop at Keylock On? menu and you΄ll have to take your battery out to turn the phone on again.GA628*#06# for checking the IMEI (International Mobile Equipment Identity)*#0000# to reset the phones menu-language to English.*#103# then YES Time and date will be shown.>*<<*<* for checking the firmware revision information (software release)>*<<*<*> 1-row text strings. if pressing yes you can check the phones text programming in currently selected language.(298 entries)>*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language.(160 entries?)The Service Provider (SP) LockThe Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.To activate/deactivate this lock one needs a special secret code that is not available to the end user.Here is how to activate the menu:<**< Lock to Network? if pressing yes you have 5 attempts to enter NCK.<**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK.Warning: Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times,the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM.Shortcut for Last Dialed call menuIf you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following keystroke instead: First '0' then '#'.Bat. level indicator when turned OFFWhen the phone is turned off and the phone is not changing - the bat. level can be seen for a short period of time by pressing the 'NO' key quick once (it has to be quick!) and then wait for about 2 sec. The bat. level will now be shown in the display at its normal position.Access menu without Sim cardTo access to the menu in your phone without having a card inside do the following: type **04*0000*0000*0000# When display say "Wrong Pin" press NO and you have access to the all menus: Info, Access, Settings, Calculator, Clock, Keylock On?,Mail, Phone book. NOTE if you try this on your phone may stop at Keylock On? menu and you΄ll have to take your battery out to turn the phone on again.Alarm Clock MenuGo to MissedCall Empty the list Press the -> key for a second or two The option Menu size turns up Choose 'yes' and go from there.An alarm clock turned up too but it never rang. I think this was because there is no clock in the phone.</blockquote>

Verification: Payakata winadi keeyak tibeda?

Top Bottom